I have always loved the idea of designing simple pieces of furniture that are both useful and beautiful. So when I came across this DIY, I was determined to make a version of it for our bedroom. We have always lived in older homes that are big on charm and short on closet space, so I’ve had most of my wardrobe in a variety of makeshift closets.
Our current master bedroom has a roomy closet built into the alcove of the second story bathroom, but it’s far removed from the laundry room and has acted more like an easy-to-access attic for storing extra bedding and out-of-season clothing.
We’d been resorting to piling clean clothes, folded or not, onto the loveseat in our bedroom rather than making the extra trip to the back of the bathroom to hang things. I know, first world problems.
I took the basic concept of the design from the DIY I saw and added a back panel on one side, not only to provide more stability to the structure, but to make it a little more interesting. I added a simple round mirror at eye level and have thought about adding a few small shelves and possibly hooks below it for accessories.
I also switched out the wooden clothes rod for a copper pipe because everything is better in copper!
Now that we have an attractive wardrobe in our room, I’m excited to keep things off the couch! Having a new piece of furniture in our space totally changes the feel of things with its height and simplicity.
It feels like the cousin of a display piece in an LA boutique. I’ve significantly paired down my wardrobe in the last year despite officially jumping on the capsule wardrobe bandwagon, but it’s still more than what I styled these photos with.
I feel like the open concept will help motivate me to keep things looking tidy, but it’s also roomy enough that even with everything I own hanging up, it won’t be overcrowded.
I can also see myself using this in my studio to hang my woven wall hangings and weaving supplies. You can easily customize this tutorial to be even more utilitarian with more shelving or hooks.
-2 – 3/4″ x 20″ x 6′ pre-cut pine boards for side panels
-3 – 3/4″ x 20″ x 36″ pre-cut pine boards for top, bottom and center supports
-1 – 3/4″ x 12″ x 6′ pre-cut pine boards for back support panel
–1 – 5′ copper pipe
-25 – #8 x 2″ brass wood screws
–8″ round mirror (optional)
–pipe cutter (or have your pipe cut down to 50″ long in the store)
-1″ drill bit
–5/64″ drill bit
Sand each piece of wood with your electric sander or regular sandpaper. If you prefer to stain or paint your panels, this is a good time to do that if you don’t mind doing some touch ups at the end. You can also wait until the end if you prefer. I chose to leave mine natural because I love the look of light wood right now.
Step One: Find the center of the short end of one 3/4″ x 20″ x 6′ panel and make a mark 1/2″ down from your short edge. Then make a mark 1/2″ down from the same edge in each corner about 1″ from the long edge. This will mark where you’ll be drilling pilot holes for your screws. Repeat with your second 6′ panel.
Step Two: Measure about 20″ up from the bottom of your 3/4″ x 20″ x 6′ panel and make a mark in the center. On the same 20″ line, make a mark 1″ in from each long edge. These will be the marks for your pilot holes for your center shelf. Make a third set of marks 4″ up from the bottom of the same panel so that you have one in the center of your board at the 4″ line and then one on each side that is 1″ from the long edge. This is where you’ll drill the pilot holes for your bottom shelf.
Step Three: Mark your 3/4″ x 20″ x 6′ panels with an ‘A’ and a ‘B’ in pencil somewhere so you can match up your measurements. It might seem like they’ll all fit, but sometimes just 1/8″ difference between holes on different panels can leave you frustrated down the line. Lean Panel A against a wall and use the pilot holes from the bottom row as your template to mark the pilot holes for the bottom shelf.
Step Four: Mark your pilot holes on the short end of your bottom 3/4″ x 20″ x 36″ panel. Mark your bottom shelf as 3 and then add an A after it so you know it belongs to the A side. Next, use the marks from the B panel to mark the opposite edge of your 3/4″ x 20″ x 36″ bottom shelf. Mark that side with a 3B so you can remember which side it belongs to. Continue the same pattern for your center shelf and top shelf.
Step Five: Measure down 5″ from the center mark on the top of each side panel and make a pencil mark. This will be your clothes hanger hole. Attach your 1″ drill bit and carefully drill a hole on each panel.
Step Six: Switch your drill bit to the other size and drill your pilot holes on the two 3/4″ x 20″ x 6′ panels.
Step Eight: Place the panel marked ‘A’ on its side on a flat surface and then place your bottom shelf up against it so that the correctly marked edge is matching. Screw your brass screws in one at a time but don’t tighten until all three are in place. Repeat this with the center shelf and then the top shelf. Then place the other side panel (Panel B) on the other side, making sure the marked side you used when you marked your holes for the shelves is facing the shelves. Screw everything together.
Step Nine: Decide which side you want your back panel on, and then make sure the edges are flush with the bottom and the side. In the photo, I’ve marked all of the places you’ll pre-drill more holes to secure this panel to the wardrobe frame. This will add another level of stability to your piece.
Step Ten: Drill your pilot holes so that you are drilling straight down into the 3/4″ edge of each panel. Be sure not to drill at an angle or you’ll bust through your wood. Then use your drill to slowly screw in your screws with the appropriate Phillips head attachment or use a screwdriver.
Place your pipe through the holes and mark the length you’d like to cut it. Remove it and cut it down to fit using your pipe cutter. I cut mine down about 10″ so that it stuck out enough on each end to act as a hook. It will fit loosely through the opening, but unless you have a dance party while choosing your outfit each day, you shouldn’t have to worry about it falling out.
The next step is adding on any extra customizations such as a mirror or hooks. I used Gorilla Glue to attach the mirror directly to the wood, but you could also hook one on or DIY a cute hanging mirror. Use the outer ends of your copper pipe to hang bags, an industrial looking light, or a hanging plant. You could also attach a larger full length mirror to the outside of your wardrobe depending on your space arrangement.
The most fun part is filling your new wardrobe with your favorite pieces! This is a great woodworking project for those of us who don’t have the space for many woodworking tools since everything is designed around the selection of pre-cut wood available.
Also, for those that may ask, this project came in at about $140 using the 20″ wide, pre-cut boards from a large chain hardware and plumbing store. To shave a little off of the cost, you could do a narrower version using the 16″ wide, pre-cut boards and a wooden dowel, but it would mean your garments might peek out the front and back of your wardrobe just a touch.
I’m so proud of myself for adding such a solid piece of furniture to our space! Are you feeling up for a weekend project? This one has your name all over it! –Rachel